Remote Power Controller 700 Series Remote Power Controllers, Up to 200 Amps, Form X, Magnetic Latching, For AC Only Applications
Series Specifications
	General   Designed to meet the requirements of MIL-C-83383   Contact Arrangement: SPST (1 Form X) Weight: 15 oz max.   Performance     Contact Ratings: For other ratings or calibrations consult the factory Power Contacts:   All Loads Up to 200 Amps @ 115 VAC Current Trip Points/Time:   1000% of Rated Current 1.0 sec. max   400% of Rated Current 10.0 sec. max   200% of Rated Current 60.0 sec. max   138% of Rated Current 1.0 hour max   Up to 115% of Rated Current No Trip Tolerances:   Current ±10%   Time ±10% Auxiliary Contacts:   Configuration SPDT   Current Rating 5 Amps @ 28 VDC Life:   • 50,000 cycles @ rated Res. And Ind. Load   • 25,000 cycles @ rated Motor load   • 100,000 cycles mechanical Rupture (main contacts): 3600 Amperes Response Time: 12 ms nom. Contact Bounce Time: 2 ms max @ rated contact load, 115 VAC Contact Voltage Drop: Initial: 225 mv @ Rated Current End of Life: 250 mv @ Rated Current Operating Voltage: Nominal AC Voltage: 104 to 122 VAC   Environmental     Temperature Range: -54°C to +71°C Vibration: 10 G'S 50 - 2000 Hz For applications requiring other vibration levels, consult the factory. Shock (Operating): 25 G's 11 ms For applications requiring other shock levels, consult the factory. Acceleration: 15 G   Electrical Characteristics     Duty Cycle: Intermittent Insulation Resistance: 100 megohms @ 500V 25°C Dielectric Strength: Sea Level:   Contact to Case 1,500 VRMS   Contact to Coil 1,500 VRMS   Coil to Case 1,500 VRMS   Across Open Contacts 1,350 VRMS 50,000 Feet:   All Points 500 VRMS   1. For other ratings or calibrations consult the factory. 2. For applications requiring higher shock and vibration, consult the factory.   The 700 Remote Power Controllers are designed to sense the current level flowing through their contacts, and to open the circuit when the current exceeds the specified current rating. These units use our unique magnetic latching motor design to minimize power consumption. These units are fully temperature compensated for accurate operation over the full temperature range. The 700 circuitry has 1500 watts of Peak Power Dissipation transient suppression built in so it can withstand the rigors of even the noisiest of supply voltages. Utilizing all space age approved materials, the 700 Remote Power Controllers are ideal for demanding applications.       Part Number       Model 700   Catalog Number Continuous Ampere Contact Rating   Thread "A"   Dimension "B" 700-5( ) 5   10-32 UNF   0.5 700-7.5( ) 7.5   10-32 UNF   0.5 700-10( ) 10   10-32 UNF   0.5 700-15( ) 15   10-32 UNF   0.5 700-20( ) 20   10-32 UNF   0.5 700-25( ) 25   10-32 UNF   0.5 700-35( ) 35   1/4-28 UNF   0.61 700-40( ) 40   1/4-28 UNF   0.61 700-50( ) 50   1/4-28 UNF   0.61 700-60( ) 60   1/4-28 UNF   0.61 700-75( ) 75   1/4-28 UNF   0.61 700-100( ) 100   1/4-28 UNF   0.61 700-125( ) 125   1/4-28 UNF   0.61 700-150( ) 150   1/4-28 UNF   0.61 700-175( ) 175   1/4-28 UNF   0.61 700-200( ) 200   1/4-28 UNF   0.61       Part Number Protocol     R.P.C. Type             Nominal Current Rating                   "A" indicates Auxiliary switch                 700 - 150 - A                        Specify Quantity   - -                                         Overall Dimensions         Schematic         Typical Wiring Diagram         Trip Time Curve     • Unless otherwise specified, all tests made at nominal coil voltages, @ 25ºC. • For special coil variations, switching configurations, terminals styles, and mounting types, consult the factory. • Unless otherwise specified, tolerances on decimal dimensions are ± .010". • Specifications contained herein are subject to change without notice.
700 Series Remote Power Controllers, Up to 200 Amps, Form X, Magnetic Latching, For AC Only Applications
Babcock, Inc. 14930 East Alondra Boulevard La Mirada, CA 90638-5752 Phone: 714.994.6500 Fax: 714.994.3013 e-mail: sales@babcockinc.com web master: webmaster@babcockinc.com Home